The stress distribution and amount of deformation has been counted under different pavage conditions.
计算不同情况下该种管道的
力分布及变
量。
;变
;畸
;变丑;残废
的;
,塑性
变
;热
变
;剪切
变
;有限
变
性;变
阻力;耐变
性
率;
变率
变;地壳变
,残留变
;
收缩量(试样的)
;压缩
变
变;风切变
;剪切
变
;轴向
变,轴向变化
阻力;抗变
性
试验
;残留变
The stress distribution and amount of deformation has been counted under different pavage conditions.
计算不同情况下该种管道的
力分布及变
量。
What should the deformation after peritonaeum eat after tumour operation?
腹膜
畸
瘤手

该吃什么?
The microstructure deformation in the aging process of the alloy has been stated ,and the heteromorphy has been found the cause of the natural aging process of the 2011 alloy .
分析了工艺参数
合金力学性能的影响,阐述了合金时效过程中的微观组织变化,找出了2011合金自然时效进程缓慢的原因是异质
核。
Aiming at difficulties in supporting dilatable soft rock roadway, control method was put forward to control effectively deformation and failure of dilatable soft rock roadway in Hongmiao Colliery.
针
红庙煤矿膨胀性软岩巷道存在的难题,给出了针
性的巷道控制方案,并在实践中得到了验证,有效地控制了红庙煤矿膨胀性软岩巷道的变
和破坏。
Through the reduction of friction force and deformation force between the steel wire and die,the tensile failure problem of steel wire workblank during the stamping process was resolved.
膨胀管的膨胀过程是一种高度非线性行为,解析方法虽然可以近似求出变
力的大小,但很难
膨胀过程进行全面求解。
As the material is deformed beyond the strain that elastic deformation persists, the stress is no longer proportional to strain, and permanent, nonrecoverable, or plastic deformation occurs.
当材料的
变超出弹性
变发生的范围,其
力将不再与
变成正比,永久的、不可回复的
变发生,即为塑性
变。
Cataclastic texture which came from brittle deformation made the jadeite quality bed, but the mylonitic texture which resulted from ductile deformation made the jadeite quality good.
在强大剪切
力和钠质流体的共同作用下,铬铁矿的淡化作用是
成绿色的主要原因。
The flow stress of the material changes with deformation, so called strain hardening or workhardening behaior and may be influenced by the rate of deformation.
材料的流量
力变化伴随着材料变
,这就是
变硬化或加工硬化特性而且会收到变
率的影响。
Investigation was made of effect of preplastic deformation for unexplosive and explosive treatments on strength, surface residual stress and hydrogen embrittlement of the specimens.
研究了预塑变
爆轰处理和未爆轰处理样品的强度、表面残留
力、氢脆敏感性及其关系的影响。
Wilder insisted that conditions like cyclopia and diprosopia should not be considered deformations, but rather "symmetrical anomalies on either side of a normal being".
怀尔德坚持认为,独眼畸
和双面畸
等状况不
该被视为畸变,
反地,
该看成是“正常生物两边
称的异常”。
The failure of directly buried heat-supply pipeline is discussed, and the design essentials are put forward in accordance with local buckling and ovalization deformation.
探讨了直埋供热管道的失效,针
局部失稳和椭圆化变
,提出了设计要点。
A new phenomenon of re-dissolution of second phases and re-formation of supersaturate solid solution found in processes of severe plastic deformation was summarized.
综述了在室温强塑性变
过程中发现的新现象:第二
颗粒的回溶,合金基体重新
成过饱和固溶体。
But in the couse of lathing and dawdling,the trouble of deformation,empyrosis and crack lf parts often appears which affects seriously the processing quality.
但在磨削过程中,易出现变
、烧伤及裂纹等问题,影响零件的加工质量。
When the regional extension is disharmonic with the basement structure and movement, complicated fault assemblages can be form during progressive deformation.
在此基础上,结合理论分析,提出了复杂断层组合成因的另一种模式——不协调伸展递进变
模式。
The present work focuses on the microscopic elastoplasticity deformation andoverall elastoplastic behaviour of metal matrix composites reinforced by short fibers.
本文研究单向短纤维增强金属基复合材料的细现弹塑性变
和宏观弹塑性响
。
The deformations of dendriform-column by FEM analysis is less than the request in the code for design of steel structures.
大型公共空间采用大型的树状支撑结构体系,不仅可行而且受力合理,完全符合《钢结构设计规范》
构件的挠度要求。
Setout ellipse curve with the traditional method of four-center will bring up offset of point and deformation of chart .
四心圆法测设椭圆曲线会造成点位偏移,图
变
。
The development of deformation theory, selection and utilization of new cultivars of Y. denudate can be based on these results.
为进一步深入开展玉兰
变理论、新品种选育和开发利用等研究提供了科学依据。
When metallic material deformation forereach its plastic limit , it will divide completely. Then the interatomic force is damaged.
断裂-金属材料在变
超过其塑性极限—完全分开.原子间结合力遭受破坏.
The results indicate that when the plastic strain is smaller than 39 5%,plastic deformation has typicality of uniserial slipping.
单晶连铸铝线材在变
量小于395%时,其塑性变
具有明显的单系滑移特征,当变
量大于395%时,才出现多系滑移特征。
声明:以上例句、词性分类均由互联网资源自动生成,部分未经过人工审核,其表达内容亦不代表本软件的观点;若发现问题,欢迎向我们指正。